WHAT'S IN THE KIT:
- 1 - Custom Lighter Trigger Sear Spring
Browning X-Bolt Trigger Spring Kit
Upgrade your Browning X-Bolt rifle with the M*CARBO Browning X-Bolt Trigger Spring Kit, the best Browning X-Bolt aftermarket trigger upgrade on the market!
This custom lighter trigger sear spring will reduce your trigger pull from a stock 4.5lbs to a modified 2.5lbs (average results can vary up to +/- 1lb), giving you a lighter and crisper Browning X-Bolt trigger. The M*CARBO browning x-bolt trigger adjustment offers a nearly 50% pull reduction, improving accuracy and overall rifle performance.
The M*CARBO Browning X-Bolt Trigger Spring Kit functions in all Browning X-Bolt models and calibers. It's the fastest and most reliable Browning X-Bolt trigger upgrade that utilizes all of the factory parts, making it a cost-effective solution to your Browning X-Bolt aftermarket trigger replacement needs.
*Please note: for the Hell's Canyon models, the Cerakote overspray must be cleaned off of the trigger sear axis pin and re-oiled, otherwise the firearm will not function safely.
Replacing your factory Browning X-Bolt trigger sear spring with this custom lighter trigger sear spring will give you the most bang for your buck. It's the best Browning X Bolt aftermarket trigger for a fraction of the cost of a complete drop-in trigger. The Browning X Bolt Trigger Job is the best way to increase your performance and accuracy right out of the box!
Improve the trigger for your Browning X-Bolt in less than 30 minutes with the M*CARBO Browning X-Bolt Trigger Spring Kit.
Current Browning Serial Number System
Browning X-Bolt Resources:
If you're getting the Browning X-Bolt Trigger Spring Kit, then you might find the following Browning X-Bolt Resources useful in further enhancing your firearm. Download the Browning X-Bolt Owners Manual or use the Exploded View of the Browning X-Bolt Parts Diagram to plan your next firearm project.
Drop Tested and Approved:
Browning X-Bolt Trigger Spring Kit is drop Tested according to SAAMI Standard Z299.5 rating (12" & 48").
Tested and Approved:
The Browning X-Bolt Trigger Spring Kit has been tested repeatedly to ensure reliable operation and safety.
ATTENTION:
You must be 18 yrs of age to purchase. We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Modifying your weapon may be prohibited in your state. Do not modify your sear or hammer engagement surfaces, with or without the Browning X-Bolt Trigger Spring Kit. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that may be incurred.
Twice pleased
I have installed this spring on two x-bolts
In less than an hour. The spring is
Perfect fit. YouTube instructions were great, both old and updated versions. Spring provided a matched 1.8 lbs trigger pull on both rifles.
Browning xbolt trigger spring
Good reduction from 4# 3oz to 2# 6oz. Not very complicated to do but watch updated video. Another suggestion is before you unpin trigger assembly to tape the bolt safety release acctuation pin to the trigger body so that it stays in proper position. Makes reassembly much easier. Then after reassembly remove the small peice of tape.
Easy install Nice feel almost zero cheap at 2.3 lbs pull
Perfect solve
Works just perfect!
The original spring is pretty stout and I was able to yank it right through the adjustment bolt hole.
Easy drop-in install of new spring and 2.5lbs pull by default.
Thanks Brothers!
Xbolt trigger spring
It was a little tricky to get the factory spring out but the mcarbo spring is simple to install and well worth the few bucks. Consistent 2 lb pulls now.
Great product at a bargain versus aftermarket trigger. Also, you keep your bolt safety feature.
mcarbo browning x bolt spring
I was a bit skeptical about the spring but after watching some youtube videos, spending 15 dollar for a spring is worth giving it a shot. I have a browning hells Canyon so i didnt want to loose the safety feature with upgrading it to the Timney trigger. I figure if it dont work out, I will upgrade it. The stock pull is too high at 4.x lbs and I tried adjusting it but it still didnt change much. The installation process was a bit hard to get the old spring out, i had to yank it out destroying my old spring. The installation of the new spring was easy. Tested 1.5lbs pull on the new spring. adjust it up to 2lbs which is where I wanted it. Well worth it.
as advertised
Few things in this life deliver what they promise. Even fewer do it for under $15. The MCarbo spring for XBolts delivered.
Received the spring. Chuckled that it looked like a bic pen spring. Followed the great video for an easy install, tightened the set screw down fully hoping to get something just under 3 lbs. Tested it with a trigger pull device. Right at 2lb 14 ounces (at heaviest setting with new spring). I'm not chuckling anymore. Y'all did us a solid by making this one.
Don Leonard
Columbus, OH
X-bolt spring
Lowered my trigger pull by 1.5 lbs. Easy install after removing the stick spring which can be tricky.
I second that question…
Will this work on the new XBolt2
Browning says it has a new “DLX” trigger in the XBolt2 speed
September 5, 2024 3:35 PM
Does it work on the new xbolt2 speed spr?
Hi, do you ship to Norway? I saw Sweden and Denmark in your shipping list but not Norway, it’s the same region over all. Thanks
Hi guys. I have a browning X-BOLT SF HUNTER II MONTE CARLO THREADED, purchased recently in Europe and manufactured in 2022. It has a silver trigger, compared to the previous versions, which featured a golden one. The gunsmith adjusted my trigger and it went down to approximately ~2,5 lbs but I still would like to make it a bit lighter.
Will the spring kit work with this model?
Pawel November 21, 2023 11:56 PM
One note said something about the hell canyon coating being an issue?
For the Hell's Canyon Models: the Cerakote overspray must be cleaned off of the trigger sear axis pin and re-oiled. Otherwise, the firearm will not function safely.
I have a browning 30-06 x bolt gold medallion that has a trigger pull of 6 pounds as the lowest will this spring help lower and fit the gun?
Kaleb October 24, 2022 4:55 PM
Yes, this spring fits all X Bolt models and it will reduce your pull. Since every firearm is different you might get a varying result from the product description.
Does the Browning X-Bolt Trigger kit only come with the sear spring and not the trigger return spring?
September 12, 2022 8:31 AM
If you look at the product description and picture, it shows the single Sear Spring being included.
Hello,
I have a 300 PRC Browning X Bolt Mountain pro long range in a tungsten finish. Will this trigger spring fit this?
Yes it will work for your model!
will this spring kit get me a 1 1/2 lbs on my browning x bolt 22/250
Hey Brother,
This will be closer to around 2.5 lbs.