KEL-TEC SUB-2000 Stainless Steel Feed Ramp:
- Will fit and function in both KEL TEC SUB 2000 9mm and 40cal versions
- Works for KEL TEC SUB 2000 Gen 2 and Gen 1
What Gen is my SUB-2000?
Best KEL TEC SUB 2000 Upgrades to replace plastic parts in critical function areas to Improve
Reliability and Performance. Replacing your plastic feed ramp with a Custom KEL TEC SUB 2000 Stainless
Steel Feed Ramp will correct KEL TEC SUB 2000 Problems with Failure to Feed Malfunctions. Custom KEL TEC SUB 2000
Accessories precision CNC machined from a block of 416 Stainless Steel.
Further enhance feeding operations by polishing your New SUB 2000 Stainless Steel Feed Ramp. Get the M*CARBO Feed Ramp Polishing Kit
here.
One of the Best KEL-TEC SUB-2000 Accessories that offers Improved
Geometry over the Factory Feed Ramp to further enhance Feeding Rounds into the Chamber of your
KEL-TEC SUB-2000.
Custom KEL TEC SUB 2000 Upgrades to ensure reliable operation of your SUB-2000 for a lifetime! The
factory plastic feed ramp is prone to wear and will melt under extreme heat from use.
Do you want us to Polish the Feed Ramp and
Install your Parts for you?
Improved Feeding Operations and Reduced Malfunctions with a Precision CNC Machined KEL-TEC SUB-2000 Stainless
Steel Feed Ramp Upgrade!
Make sure to take this opportunity to polish the KEL-TEC SUB-2000 Stainless Steel Feed Ramp to further enhance
the feeding operation in your SUB2K. Get
the M*CARBO Feed Ramp Polishing Kit here.
KEL-TEC SUB-2000 Resources:
If you're getting the KEL-TEC SUB-2000 Stainless Steel Feed Ramp, then you might find the following
KEL-TEC SUB-2000 Resources useful in further enhancing your firearm. Download the SUB-2000 Owners Manual or use the
Exploded View of the SUB-2000 Parts Diagram to plan your next firearm project.
Tested and Approved:
The KEL-TEC SUB-2000 Stainless Steel Feed Ramp has been tested repeatedly to ensure reliable operation and safety.
ATTENTION:
You must be 18 yrs of age to purchase. We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Modifying your weapon may be prohibited in your state. Do not modify your sear or hammer engagement surfaces, with or without the KEL-TEC SUB-2000 Stainless Steel Feed Ramp. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that may be incurred.
Butter Smooth
Butter smooth. I did polish it more myself. Figured why not. 0 feeding issues and it will provide longevity vs the plastic one that comes with the firearm.
Steel not plastic
A plastic feed ramp is silly. Glad Mcarbo feed ramp is available. Had to watch video to install.
Great upgrade!
This is a serious upgrade that will ensure long term reliability for my sub2000. I worry about plastic parts in critical locations on my firearms. This well engineered stainless steel feed ramp greatly raises my confidence in my Sub2000 as a long term , reliable firearm. I’ve fired several hundred rounds through mine since installation…flawless!
I upgraded the feed ramp at the same time I conducted the MCARBO trigger upgrade. I followed the step by step installation video and found it to be an easy upgrade. Polish and installation in under 2 hours. Thank you MCARBO!
Nice updgrade!
The SUB-2000 feeds so much better with this install. Extremely satisfied!
KEL-TEC SUB-2000 Stainless Steel Feed Ramp
I installed this on my sub-2000 40 cal and it was very easy to install after the polishing and works verry well.
would I buy it again yes.
I just picked up the sub-2000 9mm
No brainer upgrade
Dispels any feed ramp problems due to melting of the original, plastic, Kel-Tec Sub 2000 feed ramp. Superior quality and easy to install. I suggest the recommended ramp polishing also.
Feed ramp
Greatly enhances and cuts down on feed issues.
Stainless Feed Ramp
Super Quality; easy install; good value.
will this work on both Gen 1 and Gen 2?
Fits KEL-TEC SUB-2000 Gen 2 & Gen 1
Does this piece work for 9mm and .40 indistingtively?
The feed ramp will fit in both 9mm and .40cal models.
How difficult is it to install the steel feed ramp on the sub 2000
Hi,
Is this 416 in the annealed or is heat treated and to what hardness?
Thanks!
Dave
Hello Dave! The feed ramp is annealed, not heat treated.
Answered by
/
June 10, 2022 9:50 AM