WHAT'S INCLUDED:
- Custom Lighter SW9VE/SW40VE Sear Spring
- Assembly Dowel
S&W Sigma SW9VE & SW40VE Trigger Spring Kit
The major complaint with the Smith and Wesson SW9VE / SW40VE is that is has a very heavy 9-10lb factory trigger pull. This leaves a lot of us looking for affordable SW40VE Accessories to make further improvements on factory parts. SW9VE Accessories should include the Best Custom SW40VE Trigger Fix for the money!
Fast Installation SW9VE Trigger Job for a 50% Trigger Pull Reduction. This is a must have SW9VE Trigger Fix on your SW9VE Aftermarket Parts List!
Smith and Wesson SW9VE Trigger Kit will improve accuracy and tighten your shot groups!
Aftermarket Smith and Wesson SW40VE Parts should give you the most bang for your buck, like the Ultimate SW40VE Trigger Upgrade! One of the Best Aftermarket S&W Sigma Accessories you can make to improve your S&W Sigma Performance!
These SW9VE Accessories are also compatible as SW40VE Accessories since S&W used a lot of the same parts in their S&W Sigma trigger assemblies. Hands down the Best SW9VE Trigger Kit Available and the Only One Made by Combat Veterans! Take your SW9VE and SW40VE to the Next Level of Competition Performance!
S&W Sigma SW9VE & SW40VE Resources:
If you're getting the Smith and Wesson SW9VE / SW40VE Trigger Spring Kit, then you might find the following Smith and Wesson SW9VE / SW40VE Resources useful in further enhancing your firearm for other Smith and Wesson SW9VE / SW40VE Accessories. Download the Smith and Wesson SW9VE / SW40VE Owners Manual.
Drop Tested and Approved:
S&W Sigma SW40VE / SW9VE Trigger Spring Kit is drop Tested according to SAAMI Standard Z299.5 rating (12" & 48").
Tested and Approved:
The S&W Sigma SW40VE / SW9VE Trigger Spring Kit has been tested repeatedly to ensure reliable operation and safety.
ATTENTION:
You must be 18 yrs of age to purchase. We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Modifying your weapon may be prohibited in your state. Do not modify your sear or hammer engagement surfaces, with or without the S&W Sigma SW40VE / SW9VE Trigger Spring Kit. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that may be incurred.
It did reduce the trigger pull
The trigger pull was reduced but still a little heavy for my taste. I guess trigger safety is important on a gun with no manual safety. I did not watch the video so I am not sure what the small flexible pin tool was for.
SW9VE trigger spring kit
Spring kit arrived fast. I used the install video and it took only about an hour to install. Trigger weight before was near 10 lbs. After the install it was 7 3/4 to 8 lbs. I had hoped to be 6 or less but it was an improvement.
SW9VE Trigger Spring Kit
Had this pistol for years and it was OK but trigger was not impressive. After this kit it is enjoyable to shoot. Highly recommend.
Made the sigma a reliable fun gun to shoot
Great product! Cut my trigger pull weight from 10.6 to 4.9. Pistol is now a joy to shoot. Accuracy went up from not having to work so hard pulling the trigger. Great product and installation video. I highly recommend
It's ok
Did lighten the trigger up a bit but still well over 8lbs not 5lbs. Not a total fail but not even close to advertised trigger weight. I will say I have used other mcarbo sprin kits for other guns with great success but this one not so much
Works like a charm
This spring kit took me from a 9.6lb pull to a 4.96lb. soooo much better and easier to change than I anticipated.
New life to an old gun
Bought the SW9VE many years ago as my first home defense firearm. While being a decent gun for the low price the trigger pull was always terrible and was not enjoyable to shoot. This simple upgrade made a world of difference! It’s a whole new gun. I highly recommend.
Trigger kit. SD40VE not sure which one
Hi!
Just wanted to make sure that this spring is good to go on a model S&W40F. Thanks!
We haven't tested our spring kit in the SW40F, that was their precursor model to the SW40VE. We can't say for sure whether they made any changes with the sear spring, so unfortunately we cannot guarantee the results for your model.