KEL-TEC PMR-30 Stainless Steel Feed Ramp - New and Improved Mod 2!

After I Polish the ramp to my liking the part in stalled relatively easy I would suggest buying the take down tool I had to make my own it worked but your tool is obviously much better.90 round mag dunp no problem.

I knew when I saw these machined feed ramps they were an absolute necessity. The PRM30 has been plagued by failure to feed issues from its inception. The cause: new owners of the weapon refuse to read and/or follow the manufacturer's instructions regarding the ammunition this weapon likes to eat. Be that as it may, we owners are always trying to see what "else" we can do with our weapons and failure to feed issues, in the case of the PRM30, are born. But installing this new M-CARBO feed ramp is a MUST! From the first shot following installation, you will forget all about failure to feed issues! They're just flat gone! This is the way Keltec should have made their feed ramp to begin with but, failing that, M-CARBO came to the rescue!
The installation video shows a special tool that makes seating the feed ramp spring easier. I shouldn't just gloss over that point. Without having the proper tool(s) to get the end of that little spring into that tiny retention hole, you're likely to fail at the installation. I didn't have that little tool from M-CARBO because I didn't realize it was that critically necessary to get the feed ramp installed. I used a hemostat. I grabbed the first coil of the spring with the hemostat and locked it. Then, I was able to twist the spring (to make it tighter) and press the tip of the spring into the little retention hole. Without the hemostat, I cannot imagine a way I could have done it. If you buy this beautifully crafted feed ramp, be sure to pick up the little tool also. You won't be sorry! And you will curse the day if you don't! It's nearly impossible to install it without that little special tool. Just sayin'.
Beyond that, once I got the feed ramp installed, I manually racked the slide several times and the bullets fed flawlessly from a completely full 30-round magazine! I was so excited! Coincidentally, that same night, we had a coyote with a fresh kill singing and yodeling at our fence line, making all my dogs go nuts! Finally, at 10:30, I took my PMR30 out onto my back deck with my best flashlight. I located that coyote and with one shot, I silenced his singing. I noticed how well the second round fed up that polished M-CARBO feed ramp! And the round I fired was number 30 in the magazine! It was plumb full and it functioned flawlessly.
Get this thing! Seriously! It's the best and you will be completely satisfied with the performance of your gun once it is installed! I cannot say it enough! You need this feed ramp and your PMR30 will be your favorite gun from here on!

I ordered this part on the recommendation of a friend getting the same item. Very impressed with the updates on the part and the better material used. With that being said, I was a little disappointed with the so called fast shipping. I felt like it took longer then necessary to arrive. Took well over a week to travel from southern US to northern US.

Beautifully manufactured. Didn't really need polished but I went ahead and did it with my Dremel and a felt tip with some jeweler's rouge. Shines like a mirror and as smooth as ice. The install was very easy, simple replacement. Well thought out piece. The gun cycles smoothly with no failures. I feel much better about the reliability of my PMR-30.

I bought a PMR30 about 2 years ago.... LOVE that 22MAG, and 30 round magazine !! Pistol had some real serious feeding problems so I went to work on it. So far I have installed all of the entire M CARBO upgrades accept the new feeding ramp.... the older feeding ramp I am replacing sometime today. Keltec has discontinued phone communications from the field to order any parts which says a lot about their commitment to service and customer satisfaction.
They should issue at least 10 of the tiny retaining wire on the muzzle end of the slide guide !! PITA to deal with and install !! and impossible to find when you drop one !!
If Chris and his staff didn't provide the services/videos/improved upgrades and fast delivery services.... it's a fact.. my PMR-30 would have been in the trash bin long ago!!
Thanks Chris, you and your staff run a KICK ASS operation !! Don't let the rest of the world grind ya down !!











w

I have had my pmr for 5 years. I have bought all of these upgrades from here I have the old stainless feed ramp and this new one and I can say it matters. My feeding issues has disappeared thank you m carbo for making such a great product

 

I purchased this feed ramp for my KelTec PMR 30 with the polishing kit while skeptical about its necessity but after watching Chris’s execellant training videos,(he’s a natural) I learned a lot about my weapon's weakest parts so I dove into it. I’ve used MCarbo expertise before with my KelTec KSG and am sold on their devotion to quality CNC parts improving weapons in ways that would be, in the manufacturers mind cost prohibitive I think. I’ve used Mcarbo CNC parts for my CMR30 too which I sent to Keltec for its work, the whole Mcarbo package, and am greatly pleased with it. My PMR30 just got its facelift too now with most of the MCarbo package excepting the trigger which I may do later but cost is a factor so I did all else especially the PMR 30 feed ramp. What a difference! After I finally got it together correctly and Chris isn’t joking when I think he said that if it’s right then it’s perfect, but if it ain’t it ain’t, or some kind of gun wisdom in the video to that point. The KelTec polymer frame is a mixed blessing, soooo light weight and such a flimsy feeling thing to work with but it is remarkably strong and durable, the video Chris did really helped me to get it right finally. I will add to this review that I have a KelTec CP33 which is a fine 22LR pistol. It needed little help either, I put some KelTec 17 round mag extensions on its 33 round magazine so I can tell you that your haven’t shot a 22 until you’ve dumped 3 50 round clips into some bad guy target one after the other it will drive tacks from 50 feet with open sights, quite exciting actually, and a blast. Any way thank you Chris and MCarbo for your fine work and commitment to weapon refinement.

This really made a big difference in how my pmr fed. It just runs now! 400rds without issues. Don't think about, just do it