KEL-TEC PF9 & P11 Flat Trigger Upgrade - What's Included:
- Custom Designed KEL-TEC PF-9/P-11 Flat Trigger
- Two Black Oxide Set Screws
- One .035" Hex Key
- One .050" Hex Key
Fits & Functions in Both the KEL-TEC PF-9 and KEL-TEC P-11.
The KEL-TEC PF9 & KEL-TEC P11 Flat Trigger won't flex or warp under rapid fire like the factory plastic trigger! The M*CARBO Custom PF9/P11 Flat Trigger was designed to accommodate larger fingers or shooting with gloves on. The Flat PF9/P11 Trigger allows a more relaxed trigger face option for shooters accustomed to the new flat trigger options on the market.
The KEL TEC PF-9/P-11 Trigger Problems have a real impact on shooter performance. The major advantage to the KEL TEC PF9/P11 Trigger Replacement is that it won’t flex like the plastic trigger. New KEL-TEC PF-9 Flat Trigger for Superior Performance and Accuracy! Custom KEL TEC PF9 Accessories to correct Factory KEL TEC PF9 Problems.
The KEL-TEC PF9 Flat Trigger by M*CARBO is CNC milled out of a block of 6061 aircraft grade aluminum, then tumbled to remove sharp corners and finally hard plated with black anodizing to give it superior strength and a premium finish. This is the Ultimate Machined Aluminum Flat Trigger for your KEL TEC PF9 or P11 that will outlast and out-perform the factory plastic trigger. You will immediately notice a much smoother and more crisp trigger pull with this machined aluminum target trigger. No more flexing or jerky trigger pull. Fits & Functions in Both the KEL TEC PF9 and KEL TEC P11.
*Caution - Factory Screws may have Loctite already applied. Be careful not to strip the screws during disassembly.*
KEL-TEC PF-9 Resources:
If you're getting the KEL-TEC PF-9 Flat Target Trigger, then you might find the following KEL-TEC PF-9 Resources useful in further enhancing your firearm. Download the PF-9 Owners Manual or use the Exploded View of the PF-9 Parts Diagram to plan your next firearm project.
KEL-TEC P11 Resources:
If you're getting the KEL-TEC P11 Flat Target Trigger, then you might find the following KEL-TEC P11 Resources useful in further enhancing your firearm. Download the P11 Owners Manual or use the Exploded View of the P11 Parts Diagram to plan your next firearm project.
Tested and Approved:
The KEL-TEC PF-9 & KEL-TEC P-11 Flat Trigger has been tested repeatedly to ensure reliable operation and safety.
ATTENTION:
You must be 18 yrs of age to purchase. We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Modifying your weapon may be prohibited in your state. Do not modify your sear or hammer engagement surfaces, with or without the KEL-TEC PF-9 & KEL-TEC P-11 Flat Trigger. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that may be incurred.
Finger saver
What's to say this trigger is light years better than the original !
Amazing results
Turned a cheap pistol into a very, very good shooter. PF-9 is a very safe carry gun but factory trigger is garbage, this kits is a game changer.
Recommend stainless guide rod, guide rod spring, spring kit and flat trigger. Take your time and watch the video. You will need the right size punches to make it go smooth, not a hard project.
Very Slick Piece
Installed trigger with MCARBO trigger springs, recoil spring, and aluminum guide rod (the whole she-bang)...and WOW!!!! Night and day difference between stock. Very nice REDUCED trigger pull from stock. NOW...the install is rather straight forward especially if you watch his video. I had issues with a dead trigger (it not resetting on slide back). didn't freak out...played with the pre-travel screw a bit (screwed it almost all the way in) and trigger began resetting as it should after dry fire. I left the over travel screw alone and ground down pre-travel screw a bit and reinstalled and screwed it in and tweaked it until I had clean dry fires EVERYTIME. Took it to the range and put 10 rounds down the range and the trigger went dead on me one time...released trigger squeezed and tried again rapidly and it fired. I bought the allen key with me to the range and did a full turn and continued with the session. The remaining 40 rounds...no more issues.
TLDR...if you dont care about pre-travel and over travel...take the set screws out and put them in the spare parts bag. You dont "need" them for operation. There will be a little slack before the trigger engages the hammer but you wont have worry about sporadic dead trigger issues with the set screws. ALL in all...very slick kit MCARBO.
PF 9 Flat Trigger
I purchased the flat trigger and reduced trigger pull spring kit . There is not much adjustment on pre travel before the PF 9 will not fire , If your looking to eliminate the long trigger pull of the gun ,forget it . That's just not going to happen . You will gain a small amount of space in front of the trigger . With the reduced trigger pull spring kit installed my 6 pound trigger went down to 3 1/2 pounds .
Better than expected
I got the trigger and spring kit. What a difference!
No more pinching
pf9 flat trigger, 20lb.guide rod spring and stainless guide rod
installed these items along with previously installed trigger spring kit, it's now the gun I've always wished it would be. good going Mcarbo and thanks for the super-fast delivery
Oooh my this is
Really flat triggers are as good as they get. And really help a pistol like the P11. It makes such a difference in my well used, formerly owned P11 . The factory trigger surface shape is very hard and abusive on the finger, there is no comparison. It feels great to the trigger finger and is much easier to use when shooting. All triggers should be flat I think.
Peter S
North Tonawanda, NY
P11 flat trigger and spring kit
My old P11 had the most uncomfortable trigger of any firearm I own. I discovered after multiple attempts to utilize the over travel and take up trigger screws, that they just didn't work for me. With any amount of the take up screw protruding, the trigger will not reset, so I left it out. With a long trigger travel before the break, it wouldn't break with the over travel screw installed, so I left it out. Am I still happy? Yes!! The flat trigger and spring kit makes the P11 much more comfortable. A difference of night and day!
Why would the trigger not reset after firing the first round? Manually working the slide resets the trigger.
If you have any technical questions feel free to call into our customer service line or send us an Email at Help@mcarbo.com