This Remington 870 / 11-87 / 1100 Trigger Spring Kit consists of a custom designed and manufactured spring:
- Custom Coil Sear Spring
The Remington 870 / 11-87 / 1100 Trigger Spring Kit will reduce your trigger pull from a factory weight of 4.5 lbs to a modified weight of 3.75 lbs. The KIT spring is constructed of the highest quality spring steel available, ASTM A228 music wire and is made right here in the USA. The highest quality spring steel will help prevent malfunctions and improve performance. This trigger spring kit is designed for a lighter trap setting and is a direct improvement over the factory Remington sear spring (Part#767-175-180WB). Be advised that Remington uses the same trigger assembly in a majority of their shotguns and for this reason the MCARBO KIT will fit a variety of Remington Shotgun Models. The
MCARBO Remington 870 Trigger Spring Kit will work for the following Remington
Model Shotguns: 870,11-87,1100, , SP-10 & Rimfire Rifles 552, 572 & Autoloading
Centerfire Rifles 750, 7400, 7600, as it has the same trigger assembly as the Remington Shotguns listed
kit works for all gauges 12, 16, 20, 28 gauges and .410 bore.
This spring kit will reduce your trigger pull from a factory weight of 5.5 lbs to a modified 4 lb trigger pull. You should expect to improve your trap scores with this KIT. This KIT will reduce malfunctions and improve accuracy. Installation consists of 7 easy steps and takes approximately 15 minutes to install.
Remington 870 Resources:
Use the following Remington 870 Resources to further enhance your firearm. Download the Remington 870 Owners Manual or use the Exploded View of the Remington 870 Parts Diagram to plan your next firearm project. Print or Download the Remington 870 Trigger Spring Kit Instructions by MCARBO.
100% Lifetime Guarantee:
The Remington 870 Trigger Spring Kit is protected by the MCARBO 100% Lifetime Guarantee. This means that at any time you can send it back and we will exchange it, issue a refund or assist you in any way possible.
Tested and Approved:
The Remington 870 Trigger Spring Kit has been tested with numerous brands of ammunition to ensure reliable operation and safety.
Veteran Owned and Operated Business:
American made gun parts designed and manufactured by Combat Veterans. We will donate 5% of your purchase to the Military Foundations we humbly support.
You must be 18 yrs of age to purchase. We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Installation by MCARBO is available and recommended. Modifying your weapon may be prohibited in your state. Do not modify your sear or hammer engagement surfaces, with or without this Trigger Spring KIT. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that may be incurred.
Remington 870 Downloadable Resources
Remington 870 – Trigger Spring Kit Instructions
Tools needed are a simple hammer, a 1/32nds punch and a 2.5 inch finishing nail, and two wood blocks.
1.) First perform a 3-point safety check to insure that the chamber, bolt face and magazine well are empty.
2.) Pull the trigger to release the hammer.
2.) Push the pins out with the punch or finishing nail.
3.) Pull the trigger assembly out. Note the position of the hammer this is the “un-cocked” hammer position.
4.) Pinch and remove the stock gray spring.
5.) Depress the hammer and make sure it is in the “cocked” position.
6.) Insert the Orange spring where the gray spring once was.
7.) Re-insert the trigger assembly into the receiver. Gently tap into place.
8.) Drop in the pins and tap them in until they are flush.
9.) Cock the shotgun and test the safety, then put it on fire and pull the trigger to complete the function check.
© MCARBO 2015
Q: Which gauges will the Remington 870 trigger kit work for?
A: 12, 16, 20, 28 gauges and .410 bore
Q: Which Remington Shotguns will this kit work for?
A: The MCARBO Remington 870 Trigger kit will also work for the following Remington Model Shotguns:11-87, 1100, 552, 572, 7400, 7600, 870, SP-10.
Q: Should I be concerned with any malfunctions or light strikes after installing this kit?
A: No, all of our MCARBO Trigger Spring Kits have been professionally engineered, designed and manufactured to reduce trigger pull while maintaining 100% reliability of the firearm. You will not experience any sort of light strike or malfunction but you will experience a crisp smooth lighter trigger pull. Guaranteed or your Money Back!
MCARBO 100% Lifetime Guarantee - This means that at any time you can send it back and we will exchange it, issue a refund or assist you in any way possible.
ATTENTION: We advise that all parts purchased from our inventory be installed and inspected by a qualified gunsmith. Modifying your weapon my be prohibited in your state. Before installing please be sure to check all local state and federal laws. By installing this part you agree to take full responsibility for any and all legal, health and warranty consequences that my be incurred.
Overall Customer Rating of 35 Reviews: